It is important to hang the weights in the correct position so your clock will operate properly. (Next to the hinges on the door) (C) is Center and (L) is left. (R) Right goes on the right as you stand facing the clock. SEE FIGURE 6 TO IDENTIFY THE CHAIN VERSION.) There are small identification stickers on the bottom of each weight to tell you the position when it is hung in the clock. (SEE FIGURE 5 TO IDENTIFY THE CABLE VERSION. Use Gloves or Cloth Figure 5: CABLE DRIVEN MOVEMENTSĭO NOT REMOVE THE STYROFOAM PACKING BETWEEN THE PULLEYS AND THE CABLE DRUM ON THE CABLE DRIVE MOVEMENTS. IF YOU HAVE A LIGHTED PENDULUM, HANG P E N DULUM BEFORE YOU PLUG INTO ELECTRICITY AS THIS COULD DAMAGE THE TRANSFORMER.ĭO NOT REMOVE STYROFOAM Cable PACKING BLOCK Pulley *Note: When hanging the weights, check the hook on top and nut on bottom to make sure tight and secure Weight MAKE SURE THE FRONT OF THE PENDULUM BOB IS FACING TOWARD THE FRONT OF THE CABINET. #Old ridgeway grandfather clocks how to#STEP 2 HANGING THE PENDULUM(Figure 4)Using the diagram in Figure 4, you will be able to see how to attach the pendulum to the pendulum leader correctly. Remove the spring clip from the back side of the movement by first pulling one end free. Remove the retainer(s) by sliding the retainer(s) down off the chains. #Old ridgeway grandfather clocks free#Pull the bag free and cut the string with scissors. The chains have been packed for shipment in a bag and are located near the clock movement. Care should be taken to avoid bending the chime hammers and chime rods. CHAIN: (Figure 3B) Remove the foam pads from between the hammers and chime rods. You can remove the styrofoam blocks AFTER they become loose through normal operation, which typically occurs after eight (8) hours of run time.ĭ. Removing the styrofoam blocks at this time could cause the cables to overlap and bind the movement. This is one of the most critical points in the entire set-up operation. DO NOT REMOVE THE STYROFOAM BLOCKS from above the cable pulleys. The chime hammers will be free to move after the cardboard sleeve has been removed, thereby allowing easy removal of the foam pads. ![]() Care should be taken to avoid bending the chime hammers. Remove the foam pads from between the chime hammers and chime rods. Pull straight down and off the ends of the chime rods and pendulum guide. CABLE: (Figure 3A) Remove the cardboard sleeve, from around the chime rods and pendulum guide, by holding the cardboard sleeve at points A and B and pulling straight down. PENDULUM GUIDE CARDBOARD SLEEVESTYROFOAM CABLE BLOCKSĭ. Remove the top side panel from frame opening, bottom end first.Figure 2 Tilt the top edge of the top side panel toward the case center. Push the bottom edge of the top side panel toward the center of the case while at the same time, pull the top edge down and out of the groove in the top of the opening. Be careful not to push on the grill cloth or glass as you might separate it from the wood top side panel. Grasp the wood slats or knob with the tips of your fingers. In order to remove the panel, reach in through the front door and turn the plastic clip or remove the tape. ![]() The panels may be held in place during shipment by tape or a plastic clip. When removed, you have access to the clock movement and chime area. (Figure 2) Your clock may have wood or glass top side panels. ![]() We have placed an adjustable leveling foot on each corner to help you level the clock. The clock only needs to be sight level to operate correctly. After removing the clock from the carton, place it in its permanent location. STEP 1 UNPACKING YOUR CLOCK (Figure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ĬHOOSING THE RIGHT LOCATIONWHEN CHOOSING A LOCATION FOR YOUR CLOCK THERE ARE SEVERAL SITUATIONS OR CONDITIONS YOU SHOULD CONSIDER 1. SCISSORS (TO CUT THE RUBBER BAND HOLDING THE CHIME HAMMERS.) 3. A HELPER (FOR YOUR SAFETY AND THE CLOCKS) 2. ![]() 5 TROUBLE SHOOTING CHART, ADJUSTMENTS/REPAIRS. THINGS YOU NEED TO KNOW ABOUT YOUR CLOCKCARE TIPS FOR THE CABINET AND MOVEMENT. TABLE OF CONTENTS SET UP INSTRUCTIONS FOR CABLE AND CHAIN DRIVEN CLOCKSTOOLS YOU WILL NEED.
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |